Recent Posts

Pages: [1] 2 3 ... 10
1
General Discussion / Controller locked up - all status lights on
« Last post by bernt on April 23, 2025, 06:44:57 am »
Asking anyone for HELP resolving this issue.  My controller is offline and I am unable to get any access to it.  The status lights are all lit and solid - no flickering or cycling.  I've tried resetting the unit but none of the lights change at any point after sliding the Reset switch.  I've done a hard reboot of the controller by unplugging it, waiting a few minutes and then plugging it back in.  When power is restored all three status lights light up and remain on, steady.  In addition to not being able to access it via WiFi I'm also unable to see the Bluespray hotspot, although I assume the controller is never getting into Discovery mode.  ANY SUGGESTIONS?  Thanks!
2
Help / Re: Can't find Bluespray WFI
« Last post by BK on April 16, 2025, 12:34:50 pm »
did ya make sure the 5g was turned off. most IOTs only run on the 2.5g wifi, and seeing both bands available via the wifi causes and issue.

I'm a user, love the product, but yea, seems they've lost interest in supporting the product. They can't even post the new firmware in the forum.
Sad. Last I chatted with support, they had some new features in the horizon, but none of that transpired. Seemed it was all a gleam in their eyes.
3
Help / Re: Can't find Bluespray WFI
« Last post by richca on April 11, 2025, 04:50:23 am »
This issue is so unresolvable that I will have to replace the controller with a more reliable product. Is this company even in business anymore?
4
Help / Can't find Bluespray WFI
« Last post by richca on April 10, 2025, 01:10:27 pm »
This is a reoccurring issue and has happened once again. I cannot connect to the controller via Wi-Fi.  The controller is not discoverable following the instructions provided. Email sent to support.  The blue light flashes but the controller is not accessible from the app or the internet. 

1. Reset the controller (to make the controller forget the last wifi network):
  a. Locate the reset switch on the left side of the controller.
  b. Slide the switch down.  The amber light should flash once then pauses.
  c. When the amber light starts flashing again, let it flash 3-4 times then slide the switch up.
The controller is now reset.

2. Discovery mode
  a. Slide the reset switch down.  This time let the amber light flash all the way.
  b. When the amber light stops flashing, use your laptop or tablet and look for a hotspot named bluespray.
  c. Connect to the bluespray hotspot.
  d. Bring up a browser and type http://192.168.123.1 in your browser URL bar.
You should be able to see the BlueSpray UI.

3. Provision
  a. Click Settings->Network
  b. Click the blue wifi button next to the SSID field.  The controller will show a list of networks that it sees.  Find yours, select it, and click OK.
  c. Enter your wifi password in the Key field and click Save.
If you didn't mis-type the password, and your wifi signal is good, the controller should be able to connect to the router and tells you that it was successful.  If you did, reset and start over.

After successful provision, slide the switch up.  Connect your laptop/ipad back to your wifi network and type my.bluespray.net on the browser or you can log onto your account on our web site to access it.
5
Member Contributions / Sealing the Controller Opening
« Last post by JoeBobKing on March 27, 2025, 09:05:28 am »
I am mounting my controller in my garage, replacing the old Rainbird controller. Upon removal, I had a lot of bugs, spider webs etc everywhere inside and behind the unit. Years of environment exposure.... My mount of the BlueSpray will be made thru the back, not the bottom to hide the wires that exist thru the wall.. I needed to seal the hole, and the PERFECT option was to use 36mm Silicone plugs from amazon... 7.99 for two.

MECCANIXITY High Temp Silicone Plug Mount Dia 36mm/1.42 Inch T Shaped Rubber Stopper Hole Plugs

https://www.amazon.com/dp/B0CQR75TX7?ref=fed_asin_title&th=1
6
Help / Re: Home Automation / iPhone Button to open/close garage door
« Last post by bluespray_admin on September 05, 2022, 06:20:09 pm »
We have an API that can be called from other home automation platform.
7
Help / Home Automation / iPhone Button to open/close garage door
« Last post by DonPowell58 on July 14, 2022, 03:14:40 pm »
Does the Bluespray allow integration with home automation systems? I want to create a button on my wife's iPhone to execute (press) the Bluespray open/close the garage door? Thanks.
8
Feature Request / Can you please provide features, bug fixes, etc. for firmware 2.3?
« Last post by BK on July 09, 2022, 10:27:37 pm »
Can you please provide features, bug fixes, etc. for firmware 2.3?
9
Help / Can you please provide features, bug fixes, etc. for firmware 2.3?
« Last post by BK on July 09, 2022, 10:27:19 pm »
Can you please provide features, bug fixes, etc. for firmware 2.3?
10
Announcements / Can you please provide features, bug fixes, etc. for firmware 2.3?
« Last post by BK on July 09, 2022, 10:26:58 pm »
Can you please provide features, bug fixes, etc. for firmware 2.3?
Pages: [1] 2 3 ... 10