Recent Posts

Pages: 1 ... 8 9 [10]
91
Bug Reports / Re: Syncing the time with the web app
« Last post by edbonet@blackpith.com on November 05, 2017, 04:56:47 pm »
Restarting controller fixed the date.

But Daylight savings time problem is still there. Had to set my schedule run for 4 pm for it to water at 3 pm.
92
Bug Reports / Re: Syncing the time with the web app
« Last post by edbonet@blackpith.com on November 05, 2017, 04:29:46 pm »
Was trying to fix a daylight savings time issue.

It was suppose to feed at 3 pm Pacific, but it fed at 2 pacific.
I read the forum posts from a couple years back that said it would fix itself but it did not. It fed an hour earlier than it should and all other runs show an hour earlier.

I tried the time sync button, but now I'm in 1970 with no way to fix it.
93
Bug Reports / Syncing the time with the web app
« Last post by edbonet@blackpith.com on November 05, 2017, 04:24:20 pm »
Syncing the time with the web app makes the controller revert back to 1970.

How to fix this?
94
Help / Re: Garage Door Controller Module
« Last post by LookingForAWiFiContoller on August 27, 2017, 07:40:53 am »
Thanks for responding. I have checked the terminal ends for continuity when the garage door on Bluespray is activated. There is none. If I short the two leads coming from the garage door opener at Bluespray, the door opens and closes appropriately. I have tested the replacement relay with my bench power supply before I installed it and there was a very audible click and continuity. I have also tested it at 2.5V .05A. The click is far less audible, but switch in the relay functions correctly. I'm no electrical engineer, but my guess is that the relay isn't getting enough voltage to activate.
95
Help / Re: Garage Door Controller Module
« Last post by bluespray_admin on August 26, 2017, 08:02:05 pm »
If you can hear the relay click, that means the relay's contact is closed.  After that, it's the other side.  Check your terminal contacts.
96
Help / Garage Door Controller Module
« Last post by LookingForAWiFiContoller on August 25, 2017, 08:43:45 pm »
Well it's been almost 4 years since my last problem, and I'll be the first to say I've gotten my moneys worth with my BlueSpray. Very happy with it and that's why I'd like to fix it and keep it working. One morning I opened the kitchen door to the garage and saw the sun. The garage door failed to close at night. Sensor checks out. The wiring to the opener is good. I can faintly hear the relay on the door module click as I activate it from my phone. No continuity as the relay activates. I can't find a replacement, so I replace the JRC-21F 4100 relay with a exact model. Thank you Ebay. To my surprise, same faint click. Awww D@&%@! I can't see any damage the SMDs on the PCB. If a replacement for the module is available, I'm not sure that will fix it. Has anyone else had this happen? Thanks for reading...
97
Bug Reports / Re: Chrome and Right-Click
« Last post by bluespray_admin on August 24, 2017, 05:59:58 pm »
It does work, but not with touchscreen mode.  The UI detects the touchscreen and goes to touchscreen mode.  In this case, press and hold to simulate right click.
98
Bug Reports / Chrome and Right-Click
« Last post by berjer13 on August 24, 2017, 05:03:42 pm »
I've seen in mentioned in another thread but not addressed.  Right-click is not working with Chrome version 60.
99
Bug Reports / Re: 2.1.1 Not showing Todays Runs properly & not running programs until restart
« Last post by indo419 on July 31, 2017, 03:37:56 pm »
BlueSpray continues to halt.  Been down since 7/26/17.  Today's watering is grayed/lined out, why.  SYsLog and Firmware page attached.
Is there any way to diagnose and fix this problem?
AK
100
General Discussion / Re: lawn jpg
« Last post by bluespray_admin on July 21, 2017, 08:05:03 pm »
We've seen people using Google or Facebook just fine.  Just make sure your image is viewable by everyone and does not require login.
Pages: 1 ... 8 9 [10]