Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Panther

Pages: [1]
1
General Discussion / Firmware 2.3
« on: April 02, 2022, 11:43:43 am »
Can you please provide features, bug fixes, etc. for firmware 2.3?

2
General Discussion / TLS 1.2 Support?
« on: April 02, 2022, 11:38:19 am »
When will BlueSpray support the latest TLS version (1.2 and 1.3) and ciphers?

3
Feature Request / Re: Logging and syslog
« on: July 20, 2016, 02:49:35 pm »
After upgrading to firmware v2.1.0, the log entries appeared in the UI. The following entries appeared:

7/18/2016, 4:26:22 PM] : Sensor open - Rain sensor - tripped

[7/19/2016, 4:30:00 AM] : Water cancels - AM Schedule, AM Watering not run: System delayed

[7/19/2016, 2:23:09 PM] : Sensor close - Rain sensor

Not sure why these did not appear in previous firmware versions.


4
Feature Request / Re: Logging and syslog
« on: July 17, 2016, 07:07:35 am »
It rained last night and through the AM. I had a watering scheduled for today to start at 4am. The rain sensor tripped due to the rain. The watering did not take place and there is no record(s) of any activity in the UI system logs. The rain did not meet my "Conserve" threshold settings, so I can understand why activity associated with this did not showing up in the UI system logs. 

To simulate a sensor trip is difficult because of the location of the sensor. I believe the rain sensor is working perfectly. The controller recognizes when the rain sensor has tripped, but there's no logs associated with this activity.     

5
Feature Request / Re: Logging and syslog
« on: July 12, 2016, 05:35:27 pm »
My controller has not rebooted in over a month. It's a fact that log messages do not appear in the UI when the rain sensor is tripped. Please ensure that this is functioning correct in the next firmware update.

6
Feature Request / Re: Logging and syslog
« on: July 09, 2016, 10:54:04 am »
There is no log entry displayed in the IU, when the rain sensor is tripped. I'm running firmware v2.0.3. The only way that I know that it did not water, no log entries appear for that scheduled watering day.

7
Feature Request / Re: Logging and syslog
« on: July 08, 2016, 08:19:46 pm »
If the rain sensor is tripped, where does the controller log it to? How do I access the system log?

In the UI it states "System logs."

8
Feature Request / Logging and syslog
« on: July 04, 2016, 10:13:05 am »
I've noticed that log messages do not appear in the history tab/system logs when my rain sensor is active and cancels the water run. Log messages only appear when an option in the Weather Settings has been invoked. Please add more re-boost logging to features and capabilities.

Additionally, it would be good to have the ability to send log messages via syslog to a syslog server.   

9
General Discussion / Firmware Version: v2.0.3
« on: June 05, 2016, 11:55:49 am »
I recently downloaded and installed the latest firmware version v2.0.3. I cannot find any information about it. Can you please provide readme/release notes related to a firmware version? Please update your site with information about firmware version v2.0.3.

10
Bug Reports / Bugs Noticed after Firmware Upgrade
« on: May 25, 2016, 02:43:04 pm »
I noticed two bugs after upgrading to firmware version 2.0.2.

1) NTP server settings reset back to default settings, instead of retaining the configured/changed settings.

2) Switching between Rain, Temperature, and Wind tabs in the Weather Forecast popup does not display the data unless I close out and then select Weather Forecast again. Furthermore, when I initially open Weather Forecast, the only data that's displayed is whatever tab/option that was selected during the last Weather Forecast session. 

Pages: [1]