Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - bluespray_admin

Pages: 1 [2] 3 4 ... 21
16
If you change your router/ISP or your wifi password, you will need to provision your controller again to tell it your new wifi password.

To reset:

1. Locate the reset switch on the left side of the controller.  Slide it down for 20 seconds then slide it back up.
2. The amber linght will start flashing.  Use a laptop or tablet, look for the bluespray hotspot.
3. Connect to the bluespray hospot.  Type http://192.168.1.1 on your browser.  You will be connected to the controller.

Provision:

1. Click Setting->System
2. Click the wifi button next to the SSID field.  The controller will scan for wifi networks nearby.
3. Select your wifi network.  Make sure it has at least 3 bars.  Click OK.
4. Enter your wifi password in the Key field.  Click Save

The controller will now take your wifi information and attempt to connect to the router.  If it fails, try resetting and repeat these instruction.

If success, connect to your wifi router again.  Type http://my.bluespray.net in your browser to access your controller from now on.

17
Help / Re: Board power capacity
« on: June 20, 2017, 06:27:21 PM »
The controller's firmware does not set any limit.  The only limitation is the power supply and the water pressure.
The power supply is rated at 1A.  The board circuit trace is rated at 2A.

18
Sounds like the interface was not updated. You might want to refresh the browser every time you left it for a long time.

19
What is your firnware's build date?

20
The standby mode is designed for a quick stoppage only.  We discourage using the standby mode over a long period of time.  Putting the system in long standby result in less than desirable result.

For long idle, it's better to use delay or setting seasonal water budget to 0%.  That way, the system will automatically come back.

21
Bug Reports / Re: "Use Once" Schedule bug?
« on: May 08, 2017, 07:21:18 PM »
From the manual:

Run Once:  this run is only executed once for the duration of the selected season.  The run will be removed after the
specified season.

This is designed for instances such as when you have a new grass and you want to water it  for the 1st month.  Set up a season of that month, select the program and interval.  After the season expires, it won't run again i.e. next year.

So if you want to run it for 1 day only, set a season that lasts for 1 day.

22
Help / Re: Removal of Replaced Controller
« on: May 08, 2017, 07:05:30 PM »
You might want to email our support group, give them your account info and they'll remove it for you.

23
General Discussion / Re: Mobile interface
« on: May 06, 2017, 11:23:52 PM »
Just like in the regular UI, click to expand the Today's Run tab.  You will see the current run in green.  Click the X icon to stop it.

24
You should have uploaded the entire zip file as mentioned in this thread:

https://www.bluespray.net/forums/index.php?topic=158.0

You're lucky that it succeeded.

25
Help / Re: Display Scrambled
« on: May 04, 2017, 09:57:34 PM »
Your browser may have cached it.  Try clearing the cache and refresh the browser.

26
Did you upload the zip file or đo you unzip it and uploaded the bin file?

27
Help / Re: Can't find Bluespray WFI
« on: May 02, 2017, 12:18:14 AM »
Even if you can't access it, it would still water as scheduled.
Your controller was seen online as late as 4/29.  Was there any change to the network?

28
Help / Re: Can't find Bluespray WFI
« on: April 30, 2017, 08:33:49 PM »
As always, support @ bluespray.net.

You can also reach us from our web site.

29
Help / Re: Can't find Bluespray WFI
« on: April 30, 2017, 07:19:59 PM »
Please email our support group for assistance.

30
Help / Re: Can't find Bluespray WFI
« on: April 30, 2017, 02:12:11 PM »
You might have to reset the controller as described in this thread:

https://www.bluespray.net/forums/index.php?topic=206.0

Pages: 1 [2] 3 4 ... 21