Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Fholbert

Pages: [1]
1
Not sure where I found the link that took me to bluespray-latest-ar but clearly it was the wrong one.

I went to the support page and found the bluespray-v2.1.1-ar.zip file. Unzipped it and uploaded to my controller. ALL of my problems were fixed along with some nice upgrades. Pretty sure the old firmware file had been corrupted. 

Thanks for your help.

2
Help / Re: Display Scrambled
« on: May 05, 2017, 07:35:36 am »
Resolved by updating to latest firmware.

3
Help / Re: Display Scrambled
« on: May 05, 2017, 07:21:16 am »
I've done that. No change.

4
That's strange?

bluespray-latest-ar is a .img file. 5.37MB.

5
If I do a manual upgrade, download the file to my computer then upload the BlueSpray in get:

Please wait. Firmware update in progress.

Will Resume in xx seconds.


When it finished I'm still running the old firmware. Resetting the system does nothing.

6
My system won't upgrade 1.2.3 to 2.1.1

I've tried to upgrade with IOS, Firefox and IE. I always get the same error message.

Error: Unable to update system: firmware verification failed. 

7
Help / Re: Display Scrambled
« on: May 04, 2017, 02:54:20 pm »
It's not a network issue. I can turn the sprinklers on and off with my iPad.

The display is scrambled. Icons are missing and the layers (I guess that's what they would be called) are pushed right and left.

I hope upgrading the software will fix this issue but it won't upgrade.










8
Help / Display Scrambled
« on: April 29, 2017, 07:22:51 am »
After two years of flawless operation I have an issue.

I can see some of my BlueSpray controller on IOS but it's pretty scrambled.

On a PC running Firefox I get a blank page, no error message.

I tried to do a software up grade but it fails.

The system is working fine but I'm unable to change any settings.

I've rebooted the system, no change.

9
General Discussion / Re: Outdoor case
« on: July 26, 2014, 11:16:52 am »
I pulled new wire from three of four valve stations to reach the house. Mounted BlueSpray in my wife's closet. About a week later she noticed a funny blue light blinking behind her skirts.

10
General Discussion / Re: lawn jpg
« on: July 26, 2014, 11:12:28 am »
Google satellite view, crop the shot and import into BlueSpray.


11
General Discussion / Re: Different days on different stations.
« on: June 25, 2014, 10:56:05 pm »
Good info, thanks for the help.

12
General Discussion / Re: Different days on different stations.
« on: June 25, 2014, 07:05:14 pm »
Thanks for your help.

One of the reasons I purchased BlueSpray was to get away from three separate systems I currently have. I have to watch when it gets really hot and I add X minutes to each station that I don't run over into the start time of the next controller because I don't have enough water pressure to run two systems at the same time.

With one 16 station BlueSpray system running different start times could I still have that problem?

13
General Discussion / Different days on different stations.
« on: June 22, 2014, 11:03:37 am »
My new BlueSpray arrived Friday, I'm trying to set up the zones.

I'm wanting zones 1-11 to run daily. Zones 12, 13 and 14 to run odd days and zone 15 to run once a week.  Is that not possible? I suspect there is a work around to make this happen.

Pages: [1]